| Application |
|---|
| Application | Sum function, for general industrial use |
| Installation | pipe connection with adapter |
| Medium | Conductive liquids, Water, water-based liquids |
| Medium note | | Conductivity: ? 20 µS/cm | | Viscosity: < 70 mm?/s (40 °C) |
|
| Measured medium temperature [°C] | -10…70 |
| Pressure strength [bar] | 16 |
| MAWP (for use according to CRN) [bar] | 17.7 |
| Electronic data |
|---|
| Operating voltage [V] | 18…30 DC, (according to EN 50178 SELV/PELV ) |
| Current consumption [mA] | 95, (24 V) |
| Min. insulation resistance [M?] | 100, (500 V DC) |
| Protection class | III |
| Reverse polarity protection | yes |
| Power-on delay time [s] | 5 |
| Inputs/outputs |
|---|
| Number of inputs and outputs | Number of digital outputs: 2, Number of analog outputs: 1 |
| Inputs |
|---|
| Inputs | counter reset |
| Outputs |
|---|
| Total number of outputs | 2 |
| Output signal | switching signal, analog signal, pulse signal, IO-Link, (configurable) |
| Electrical version | PNP/NPN |
| Number of digital outputs | 2 |
| Output signal function | normally open / normally closed, (parameterizable) |
| Max. voltage drop DC switching output [V] | 2 |
| DC switching output load current [mA] | 200 |
| Number of analog outputs | 1 |
| Analog current output [mA] | 4…20, (scalable) |
| Max. load [?] | 500 |
| Analog voltage output [V] | 0…10, (scalable) |
| Min. load resistance [?] | 2000 |
| Pulse output | Flowmeter |
| Short-circuit protection | yes |
| Short-circuit protection type | clocked |
| Overcurrent protection | yes |
| Measurement/setting range |
|---|
| Range measurements | | 0.1…25 l/min | 0.005…1.5 m?/h |
|
| Display range | | -30…30 l /min | -1.8…1.8 m?/h |
|
| Resolution | |
| Setting point SP | | 0.25…25 l/min | 0.015…1.5 m?/h |
|
| Reset point rP | | 0.1…24.9 l/min | 0.005…1.495 m?/h | < /tbody>
|
| Analog start point nala, ASP | |
| Analogue Endpoint, AEP | |
| Step width | |
| Momentary flow control |
|---|
| Impulse value | 0.00001…30 000 m? |
| Pulse length [s] | 0.01…2 |
| Temperature control |
|---|
| Measuring range [°C] | -20…80 |
| Resolution [°C] | 0.2 |
| Setting point SP [°C] | -19, 2…80 |
| Reset point rP [°C] | -19.6…79.6 |
| Analog start point [°C] | -20…60 |
| Analog end point [°C] | 0 …80 |
| In steps of [°C] | 0.2 |
| Accuracy/Uncertainty |
|---|
| Flow rate control |
|---|
| Accuracy (in measuring range) | ± (0, 8% MW + 0.5% MEW) |
| Repeatability | ± 0.2% MEW |
| Temperature control |
|---|
| Accuracy [K] | ± 2.5 (Q > 1 l/min) |
| Response Time |
|---|
| Flow Rate Control |
|---|
| Response Time [s] | 0.15, (dAP = 0) |
| Programmable delay time dS, dr [s] | 0…50 | 0…50 | 0…50 | |
| Switching output damping dAP [s] | 0…5 |
| Temperature monitoring |
|---|
| Dynamics of response T05 / T09 [s] | T09 = 20 (Q > 1 l/min) |
| Software / Programming |
|---|
| Parameter selection | Flow control, flow meter, pre-set counter, Temperature control, hysteresis / window , normally open / normally closed, switching logic, current output / voltage output / pulse output, Start delay, display can be switched off, Display |
| Interfaces |
|---|
| Communication interface | IO-Link |
| Transmission method | COM2 (38.4 kBaud) |
| IO-Link test | 1.1 |
| SDCI standard | IEC 61131 -9 |
| IO-Link device ID | 569 / 00 02 39 h |
| Profiles | Smart Sensor: Process Data Variable, Device Identification, Device Diagnosis |
| SIO mode | yes |
| Desired port type | A |
| Analog operating data | 3 |
| Binary operating data | 2 |
| Minimum time duty cycle [ms] | 5 |
| Operating conditions |
|---|
| Ambient temperature [°C] | -10…60 |
| Storage temperature [°C] | -25…80 |
| Degree of protection | IP 67 |
| Tests / approvals |
|---|
| EMC | |
| Impact resistance | | DIN IEC 68-2-27 | 20 g (11 ms) |
|
| Vibration resistance | | DIN IEC 68-2-6 | 5 g (10…2000 Hz) |
|
| MTTF [years] | 162 |
| Pressure Equipment Directive | Good engineering practice, can be used for fluid group 2, fluid group 1 on request |
| Mechanical data |
|---|
| Weight [g] | 542.5 |
| Material | stainless steel steel (1.4404 / 316L), PBT-GF20, PC, FKM, TPE medium | stainless steel steel (1.4404 / 316L), PEEK, FKM |
| Process connection | Threaded connection G 1/2 DN15 Flat seal |
| Displays / Controls |
|---|
| Display | | Display | 6 x LED, green (l/min, m?/h, l, m?, 10?, °C) | | Output status | 2 x LED, yellow | | Measured values | alphanumeric display, 4 digits | | programming | alphanumeric display, 4 digits |
|
| Notes |
|---|
| Notes | | MW = Measured value | | MEW = Upper limit of measuring range |
|
| Pack quantity | 1 piece |
| electrical connection |
|---|
| Connection | Connector: 1 x M12, Contacts: gold-plated |
| Diagrams and Graphs |
|---|
| Pressure Loss | | dP | Pressure loss |
|---|
| Q | volumetric consumption |
|---|
|
|---|
